The CC1150 is a true single chip UHF transmitter designed for extremely low power wireless applications. The circuit is primarily used in the 315-, 433-, 868-, and 915-MHz bands of ISM(Industrial, Scientific, and medical) and SRD(Short range devices), but can easily be programmed to run on other frequencies in the 300-348 MHz, 400-464 MHz, and 800-928 MHz bands.
The DS18B20 digital thermometer provides 9 - to 12-digit Celsius temperature measurement and features a non-volatile alarm function with user programmable up and down trigger points. The DS18B20 communicates over a 1-wire bus, which by definition requires only one data line (and ground) to communicate with the central microprocessor.
The CY22381 is a next-generation programmable Flash programmable clock for networking, telecommunications, data communications, and other general purpose applications. The CY22381 offers up to three configurable outputs in an 8-pin SOIC, powered by a 3.3V power supply.
The LTC 2351-14 is a 14-bit, 1.5Msps ADC with six sampled differential inputs. The device only obtains 5.5mA from a single 3V power supply and uses a micro 32 pin (5mm × 5mm) QFN package. Sleep shutdown mode further reduces power consumption to 12 μ W。 The combination of low power consumption and small packaging makes the LTC 2351-14 suitable for portable applications.
The ISL9301 is a fully integrated high input voltage single-cell lithium-ion battery charger with power path management capabilities. The charger performs CC/CV charging functions required for lithium-ion batteries. The charger accepts an input voltage of up to 28V, but will be disabled when the input voltage exceeds the 10.5V OVP threshold.
The DCV01 series is a series of 1-W, 1500-Vrms isolated, unregulated DC/DC converter modules. The DCV01 family of devices requires minimal external components and includes on-chip device protection that provides additional features such as output disabling and synchronizing switching frequencies
The TMP411 device is a remote temperature sensor monitor with a built-in local temperature sensor, available in VSSOP-8 and SOIC-8 packages. Remote temperature sensors and diode connected transistors are typically low-cost NPN or PNP type transistors or diodes that are part of microcontrollers, microprocessors, or fpga.
IDT5V49EE902 is a programmable clock generator for high performance data communications, telecommunications, consumer and networking applications. There are four internal PLLS, each individually programmable to allow for four unique non-integer correlated frequencies. The frequency is generated by a single reference clock.
The AD7892 is a high-speed, low-power, 12-bit a/D converter powered by a single+5V power supply. The device contains a 1.47 µ s successive approximation ADC, an on-chip tracking/holding amplifier, an internal+2.5 V reference, and an on-chip general-purpose interface architecture that allows serial and parallel connections to microprocessors.
The X9221A integrates two digitally controlled potentiometers (XDCPS) on a single chip CMOS integrated microcircuit. The digital control potentiometer is realized by a series array of 63 resistance elements. XDCP can be used as a three-terminal potentiometer or a two-end variable resistor for a variety of applications including control, parameter adjustment, and signal processing.
The 33884 Switch monitoring interface is a monolithic silicon integrated circuit (IC) to perform switch monitoring functions. The device provides an efficient interface between an electrical switch and a low-voltage microprocessor. The 33884 provides pull-up and pull-down currents for switch contacts while monitoring input voltage levels.
The AD8226 is a low-cost, wide-range instrument amplifier that requires only one external resistor to set the gain between 1 and 1000. It is designed for various signal voltages. Using an 8-pin MSOP and SOIC package, it is fully suitable for operation from − 40 ° C to+125 ° C. Ideal for industrial applications with multiple channels and limited space.
The LT1110 is a multifunctional micro-power DC-DC converter. The device requires only three external components to provide a fixed output of 5V or 12V. The extremely low 1.0V minimum supply voltage allows the LT1110 to be used in applications where the main supply is a single battery.
The ADT7475 controller is a thermal monitor and multi-PWM fan controller for noise-sensitive or power-sensitive applications requiring active system cooling. The effectiveness of the system's thermal solution can be monitored using THERM inputs. The ADT7475 also uses two-way THERM pins as an output to provide critical thermal protection to the system to prevent overheating of the system or components.
The KA3846 control IC provides all the necessary features to achieve a fixed frequency, current mode control scheme while maintaining a minimum number of external parts. The superior performance of this technology can be measured by improved line regulation, enhanced load response characteristics, and simpler, easier to design control loops.
AH1807 is a medium sensitivity micro power all polarity Hall effect switch IC designed for magnetic tamper detection in battery powered consumer products, household appliances, and industrial devices such as smart meters. Based on two Hall effect plates and a chopper stabilized architecture, the AH1807 provides a reliable solution across the entire operating range.
The LT1963 series is a low dropout regulator optimized for fast transient response. The device can provide an output current of 1.5A and a voltage drop of 340mV. These devices have adjustable devices with a fixed output voltage of 1.5V, 1.8V, 2.5V, 3.3V, and a reference voltage of 1.21V. The LT1963A voltage regulator has a 5-pin TO-220, DD, 3-pin SOT-223, 8-pin SO, and 16-pin TSSOP package.
The LP87332A-Q1 is designed to meet the power management requirements of the latest processors and platforms in automotive camera and radar applications. The device has two buck DC/DC converters, two linear regulators, and two general-purpose digital output signals. It supports remote voltage sensing to compensate for the IR drop between the regulator output and the load point (POL), thereby improving the accuracy of the output voltage.
